ARTICLE

The Shear Clearance Nobody Checks Is the One That Costs You Parts

Ask a shop why its sheared edges are worse than they were last year and you will usually hear one answer: the blades are dull.

So the blades get sharpened. Sometimes that helps. Often it doesn't, because sharpness was never the main variable. The variable that quietly decides edge quality on a shear is blade clearance — the gap between the upper and lower blades, usually expressed as a percentage of material thickness — and in most shops it is set once, forgotten, and then blamed on everything except itself.

This article is about the guillotine shear — the QC11K type, where the moving beam travels straight down in its guides. That design is the reason clearance deserves an article of its own: on a guillotine, the gap is not a fixed property of the machine. It is a setting, it can be adjusted along the full length of the blades, and on CNC models it can be driven and recalled from the control. (A swing-beam shear, whose beam pivots and whose rake angle is fixed, plays by different rules — a subject for another day.)

A shear does not cut like a knife. It fractures. The upper blade presses the sheet down into the lower blade, the material deforms, and at some point a crack starts from the top edge and another from the bottom edge, and the sheet separates when those two cracks meet. Everything about edge quality follows from how those cracks meet.

 

 

What clearance actually does

 

Set the clearance too wide and the sheet is not sheared so much as torn. The top blade pushes the material down and sideways before the crack starts, so the edge rolls over, the burnished zone — the smooth, shiny band where the blade actually polished the metal — shrinks, and the fracture zone takes over. The burr at the bottom grows. On thin sheet the strip also bows and twists as it leaves the blades, because the wide gap lets it bend instead of constraining it.

Set the clearance too tight and the opposite failure appears. The cracks from the top and bottom edges no longer meet cleanly; they pass each other, and the blade has to plough through the remaining ligament. Edge quality can look deceptively smooth, but the force goes up, the blades wear faster, the edge work-hardens more, and on thicker material you can stop the machine entirely.

Between those two failures is a window, and the window moves. Mild steel, stainless and aluminium all want different clearances at the same thickness, and the right percentage changes as the sheet gets thicker. This is why "we set it at 8% years ago" is not a process. It is a hope.

 

 

On a guillotine, clearance has an address: everywhere

 

Because the guillotine's beam descends in a straight line, the clearance is supposed to be the same at the left end of the blades, in the middle, and at the right end. When it isn't, the sheet tells you: the edge changes character along its own length. A strip that leaves one end clean and the other end burred is not a blade problem or a material problem. It is a gap that is right in one place and wrong in another — guides worn, a blade seated unevenly after a change, an adjustment made at one end and never verified at the other.

This is also where the guillotine's second setting earns its keep. The rake angle — the incline of the moving blade — trades force against distortion. Open the rake up and the machine cuts thicker material with less force, because only part of the blade is engaged at any moment; but the cut-off strip pays for it in bow, twist and camber, worst on narrow strips. Close the rake down and strips come off flatter, at the cost of higher force. A shop that only ever adjusts one of the two settings is tuning half the machine.

 

 

The evidence is on the edge, if you read it

 

A sheared edge tells you its own history. Rollover at the top tells you the sheet bent before it broke — a sign of excessive clearance or a dull edge. A wide, bright burnish zone with a clean fracture below it is what a healthy shear looks like. A burr you can feel with a fingernail is the fracture finishing late and tearing instead of separating.

None of this requires instruments. It requires looking at the edge before the part moves on, which is a habit, not a purchase.

 

 

Why the press brake inherits the shear's mistakes

 

Here is where a shearing problem becomes a bending problem, and why the two machines should never be troubleshot separately.

A sheared edge is work-hardened and, if the clearance is wrong, carries a burr and residual stress along its length. Put that edge on the outside of a bend — which happens constantly, because nobody marks which edge was which — and you have placed hardened, torn material at the point of maximum stretch. The crack that follows gets blamed on the radius, the material, or the press brake. The shear that made the edge is two departments away and already forgotten.

The same logic applies to the strip itself. A blank that left the shear bowed or twisted does not sit flat on the backgauge. The operator chases angle variation that was manufactured upstream, one strip at a time.

 

 

A clearance routine that fits in a shift

 

You do not need a laboratory to control this. You need a routine short enough that it actually happens:

· Write the clearance down per material and thickness. A laminated card on the machine beats a setting in someone's memory. When the job changes from 2 mm mild steel to 3 mm stainless, the card changes with it.

· Test-shear and read the edge. One strip, thirty seconds: rollover, burnish, burr. If the burr catches a glove, the clearance or the blade edge needs attention before production, not after scrap.

· Sharpen on evidence, not on calendar or on panic. Blades that are sharp but run at the wrong clearance will still make bad edges. Clearance first, sharpness second — in that order, every time.

· Mark the burr side on bend-critical blanks. The burr side faces the inside of the bend, where the metal is compressed. This is a pencil mark at the shear. It costs nothing and it prevents the most predictable cracking there is.

· Re-check after every blade change or regrind — at three points. A reground blade is not the same blade. The clearance that was right before the grind is a starting guess after it, and on a guillotine it has to be verified left, centre and right, because the gap you set is only the gap you measured.

Shops that do this stop having the argument about whether the bending department or the cutting department owns the problem. The edge carries the answer, and the edge was made at the shear.

 

 

Where this leaves the buying decision

 

None of the above requires a new machine. A well-maintained shear with a disciplined clearance routine will out-produce a new shear run on memory and habit. If your edges are inconsistent, the first investment is a card, a marker and ten minutes of training — not equipment.

Where equipment does enter the picture is repeatability. On a CNC guillotine shear, blade clearance and rake angle are set from the control and can be stored per material and thickness, so the night shift runs the same edge quality as the day shift instead of inheriting whatever the last operator dialled in. That is the moment a guillotine shear stops being a machine the operator guesses at and becomes part of a controlled process — the same transition this blog has described for press brakes, panel benders and laser cutters.